Copper Fishing Wire Connections

Copper Fishing Wire Connections

The most durable and reliable connection for backer-to-copper is the  Blood Run Micro Swivel/heatshrink connection method.  Based upon feedback from our dealers who perform bulk line winding services, this method proves to be the most reliable connection method for most fishermen.

While we strongly advocate usage of the Uni Knot for our copper to backer connections just for time savings and simplicity, the swivel/heatshrink method is by far the most often used and maintenance free of any connection.

For our recommended usage of the Uni Knot, bend the copper in a 180 degree bend with about 3-4" of copper.   Bring your backer up through the "eye" of the bend, then go long about 3" and pinch your backer to the two pieces of copper (tag and mainline).   Then "backwrap" the braid or mono tag end around the two pieces of copper underneath your loop.    Put the tag end of the backer back down through the "eye" you came up through and slowly draw the knot down towards the "eye".   The knot should snug right down to the "eye" of the copper and you are set.   In the case of braid, we like to perform two half-hitches with the tag end of the braid before trimming.    Trim the remaining tag end of the copper and you have the perfect low profile copper knot.   We use and recommend this for both backer to copper and copper to leader connections.

For the swivel/heatshrink connection, you can purchase our pre-packaged Copper Fishing Wire Connection Kit.   Simply take your copper end and slide down a 1-2" piece of heatshrink tubing, large enough in size to cover the whole connection when finished.   Then, loop the copper end through one eye of the Power swivel so you have approximately 2 inches of tag end copper remaining.

Take this tag end and haywire twist it to the main copper line below the swivel, make sure the twist is tight and compact.     This is easily accomplished by pinching and twisting the tag end with the mainline copper as you move away from the swivel.  

Then, pinching both the swivel and the end of your haywire twist, TWIST THE SWIVEL ONLY to compress your haywire twist.    This will enable the heatshrink to slide over your twist.

Slide the heatshrink tube up over the haywire twist and up on to the bottom part of the swivel, and apply heat.  Do not slide the heatshrink up past the halfway point of the swivel, as it will not allow the swivel to spin properly.

Your backer to swivel connection can be virtually any kind of knot, double cinch, etc.

Your copper to leader connections DO NOT need a swivel or heatshrink connection.   These knots do not receive the same amount of abuse and stress that the copper to backer knots receive.   A simple Uni knot here will suffice.

ブログに戻る

2件のコメント

I read in a post to run the 45lb copper through the swivel eye twice before making the haywire twist? Is that critical? I can’t get your 45lb copper through a spro size 8, 50lb, swivel twice. Thanks – Taylor
———
Blood Run Fishing replied:
It is not life or death critical, but it is important we feel, and we do it every time. We can’t speak to the Spro size 8, but the copper does fit through our size 8 and even more easily our size 7 (what we personally use).

Hope that helps!

Blood Run Fishing bloodrunfishing.com 5 The supporting cast to your fishing story #bloodrunfishing 6
Taylor Stratton

If using the swivel and heat shrink tubing method of splice/knot , is standard electrical shrink ok?
———
Blood Run Fishing replied:
Any heatshrink can be used as long as it is small enough to pass through your levelwind on your reel.

Blood Run Fishing bloodrunfishing.com 4 The supporting cast to your fishing story #bloodrunfishing 5
John Neureuther

コメントを残す

コメントは公開前に承認される必要があることにご注意ください。